Our products are to comply with environmental requirements in accordance with SONY code no. SS-00259 withrestrictions of 10 harmful materials.
Features ‧ Small size and light weight with size range per international standard ‧ Highly stable in auto-placementsurface mounting application ‧ Compatible with both wave soldering and reflow soldering.
Size | L | W | T | C | D |
0201 | 0.60±0.03 | 0.30±0.03 | 0.23±0.03 | 0.15±0.05 | 0.15±0.05 |
0402 | 1.00±0.10 | 0.50±0.05 | 0.35±0.05 | 0.20±0.10 | 0.25±0.10 |
0603 | 1.60±0.10 | 0.80±0.10 | 0.45±0.10 | 0.25±0.15 | 0.30±0.15 |
0805 | 2.00±0.10 | 1.25±0.10 | 0.50±0.10 | 0.35±0.20 | 0.40±0.20 |
1206 | 3.10±0.10 | 1.55±0.10 | 0.55±0.10 | 0.45±0.20 | 0.40±0.20 |
1210 | 3.10±0.10 | 2.50±0.10 | 0.55±0.10 | 0.45±0.25 | 0.45±0.25 |
1218 | 3.10±0.10 | 4.60±0.10 | 0.55±0.10 | 0.45±0.25 | 0.45±0.25 |
1812 | 4.50±0.10 | 3.10±0.20 | 0.55±0.05 | 0.55±0.20 | 0.70±0.20 |
2010 | 5.00±0.20 | 2.50±0.15 | 0.55±0.10 | 0.60±0.25 | 0.50±0.25 |
1225 | 3.10±0.15 | 6.30±0.15 | 0.90±0.15 | 0.60±0.30 | 0.80±0.25 |
2512 | 6.35±0.20 | 3.10±0.15 | 0.55±0.10 | 0.60±0.25 | 0.60±0.25 |
Type | RCTO1 | RCT02 | RCTO3 | RCT05 | RCT06 | RCT10 | RCT18 | RCT12 | RCT20 | RCT25 | RCT22 | |
Size | 0201 | 0402 | 0603 | 0805 | 1206 | 1210 | 1812 | 1218 | 2010 | 2512 | 1225 | |
Power Rating at 70℃ | 1/20W | 1/16W | 1/10W | 1/8W | 1/4W | 1/3W | 1/2W | 1W | 3/4W | 1W | 2W | |
Max RCWV | 25V | 50V | 75V | 150V | 200V | 200V | 200V | 200V | 200V | 200V | 200V | |
Max Overload Voltage | 50V | 100V | 150V | 300V | 400V | 400V | 400V | 400V | 400V | 400V | 400V | |
Jumper<50mΩ | 0.5A | 1A | 1A | 2A | 2A | 2A | 2A | 2A | 2A | 2A | 10A | |
Operating Temperature Range | -55~+155°℃ | |||||||||||
Standard Resistance Range | 0Ω | 0~50mO | ||||||||||
±1%(E-96) | 12~10MO | 12~10MΩ | 10Ω~ 20KΩ | |||||||||
±5%(E-24) | 12~10MΩ | 12~22MΩ |
ITEM | SPECIFICATION | TEST METHOD |
Solderability | Over 95%of termination must be covered with solder | JIS C 52014.17/MIL-STD-202G METHOD 208H / IEC 60115-14.17 Reflow Soldering:Bath temperature:(235±5)℃,Immersion time:(2±0.5)s WAVE Soldering:Bath temperature:(270±10)℃,Immersion time:(2±0.5)s |
Resistance to Solder Heat | J、G:△R≤±(1%+0.05Ω) F:△R≤±(0.5%+0.05Ω) No mechanical damage | JIS C 52014.18/MIL-STD-202G METHOD 210F/IEC 60115-14.18 The temperature of the solder bath shall be (260±5)°℃,The immersion time shall be(5±0.5)s or(10±1)s as prescribed by the detail specification |
Temperature Coefficient of Resistance (TCR) | 0402&0201: 12~102;>3.3M:±400ppm/℃ 102(excluding 102)~3.3M: ±200ppm/℃ 0603 or above: 1Ω~10Ω;>1M:±200ppm/℃ 102(excluding102)~1M: ±100ppm/℃ | JIS C 52014.8/MIL-STD-202G METHOD 304/IEC 60115-14.8 The temperature characteristic or temperature coefficient of resistance is not specified for resistance values of less than 5R owing to difficulty of accurate measurement |
Short Time Overload | J、G:△R≤±(2%+0.05Q) F:△R≤±(1%+0.05Ω) | JIS C 52014.13/IEC 60115-14.13 2.5×Rated voltage or Max.Overload Voltage for 5 sec measure resistance after 30 minutes |
Load Life Humidity | J、G:△R≤±(3%+0.05Ω) F:△R≤±(1%+0.05Ω) | JIS C 52014.24/MIL-STD-202G Method 106G/IEC 60115-14.24 Maintain the temperature of the resistor at 40±2℃ and 90~95%RH with the rated voltage applied.Cycle ON for 1.5 hours and OFF for 0.5 hour for1000+48/-0 hours.After 1~4 hour,measure the resistance value |
Load Life | J、G:△R≤±(3%+0.05Ω) F:△R≤±(1%+0.05Ω) | JIS C 52014.25/MIL-STD-202G Method 108A/IEC 60115-14.25 70±2℃,Max.working voltage for 1000 hrs with 1.5 hrs “ON”and 0.5 hrs “OFF”. |
Temperature Cycle | J、G:△R≤±(1%+0.05Ω) F:△R≤±(0.5%+0.05Ω) No mechanical damage | JIS C 52014.19/MIL-STD-202G Method 107G /IEC 60115-14.19 Repeat 5 cycles as follows -65℃(30 min.)+25℃(2~3 min.)+125℃(30 min.)+25°℃(2~3 min.) |
Insulation Resistance | Between termination and coating must be over 1000MΩ | JIS C 52014.6/MIL-STD-202G Method 302/IEC 60115-14.6 Test voltage:100±15V |
JIS C 52014.33/MIL-STD-202G Method 211A/IEC 60115-14.33 | ||
J、G:△R≤±(1%+0.05Ω) | Resistance change after bended on the 90mm PCB | |
Bending | F:△R≤±(0.5%+0.05Q) | Bend:3mm for 0201、0402、0603、0805、1206 |
Strength | No mechanical damage | 2mm for 1210、1812 、1218、1225 |
lmm for 2010、2512 |
Why choose us?
1.Fast delivery time
With adequate monthly capacity of SMD resistors 15 Billion PCS and through hole resistors 20 Million PCS, we can secure fast delivery time to all the customers.
2. High quality
With more than 39 years in the industry, we well know the relevant standards and manufacture products based on requirements, also we have perfect quality system and tools to monitor the product from raw materials to finished products to secure quality .
3. Professional and reliable team
With a professional and experienced team, we understand every requirement of our customers and always try out best to satisfy them.
4. Quick Response
If you have any enquires or problem, please feel free to contact with us, we will try to answer you within 24 hours.
F.A.Q
Question 1
Question: Does the sample fee can be returned?
Answer: We can provide free samples.
Question 2
Question: How long will it take to receive my order?
Answer: The lead-time depends on your order quantity and destination.
Welcome to contact us freely for more details about our products!
Home About HKR Products Application Service Resources News Contact Us